Licensed Georgia electrical contractor serving homes, businesses and industrial sites
404-507-6173 | info@hwspartners.com
ELECTRICAL PANEL UPGRADE ATLANTA GA
Need an electrical panel upgrade Atlanta GA homeowners and businesses can count on? H & W Solution Partners LLC replaces outdated, overloaded and unsafe panels with new 200 amp service sized for the way you use power today. We pull the permit, coordinate the utility disconnect, pass the inspection and label every circuit before we leave.
ALL PROPERTY TYPES
Homes, businesses, industrial
PERMITS HANDLED
Pulled, inspected, closed
LICENSED
Georgia electrical contractor
12+ YEARS
in the electrical trade
Electrical Panel Upgrade Atlanta GA: What Your Panel Does
Your electrical panel, also called a breaker box or load center, is where utility power enters the building and gets divided into individual circuits. Each breaker protects one circuit and trips when that circuit draws more current than its wire can safely carry. When a panel is undersized, worn out or a known problem brand, those breakers stop doing their job reliably, and that is when an electrical panel upgrade Atlanta GA homeowners keep putting off becomes a safety issue.
Many homes across metro Atlanta were built with 60, 100 or 150 amp service. That was plenty for a few lights, a range and a window unit. Today the same panel may be feeding central air or a heat pump, an electric dryer, a home office, a tankless water heater and an EV charger, all at once on a hot August evening.
A panel upgrade replaces the old load center with a new one rated for more capacity, usually 200 amps for a single-family home. Depending on what we find, the job can also include a new meter base, new service entrance conductors and an updated grounding system, so the whole path from the utility to your breakers meets current code.
PARTS OF YOUR ELECTRICAL SERVICE
Service entrance conductors
The wires that carry power from the utility to your meter and panel.
Meter base
Where the utility meter mounts. Larger service often needs a larger meter base.
Main breaker
Shuts off the whole panel and sets its rated capacity, such as 200 amps.
Branch breakers
One for each circuit, sized to the wire it protects.
Grounding and bonding
Ground rods, pipe bonds and connections that carry fault current safely to ground.
Panel Replacement Atlanta: Warning Signs to Watch For
Most people do not think about the panel until something goes wrong. If you notice any of these, book an assessment. Some are quick repairs, and others mean it is time for a panel replacement Atlanta homeowners should not keep putting off.
Breakers that trip often
Resetting the same breaker again and again means the circuit or the panel itself is overloaded.
Flickering or dimming lights
Lights that dip when the AC, dryer or microwave starts point to a panel struggling under peak load.
A warm panel cover
Heat on the door or the wall around it can mean loose connections or breakers that no longer trip correctly.
Burning smell or scorch marks
Melted plastic, darkened breakers or a burning odor need a licensed electrician right away.
Buzzing or crackling
A steady hum or crackle from the panel often means arcing at a loose or damaged connection.
A fuse box
Screw-in fuses are easy to oversize and give less precise protection than modern breakers.
Federal Pacific, Zinsco or Challenger
These brands have well-documented breaker problems, and many insurers ask about them by name.
No open spaces or double taps
Two wires on one breaker, or a panel packed with tandem breakers, means it has run out of room and may need a breaker box replacement Atlanta inspectors will accept.
Rust or water stains
Moisture inside a panel corrodes bus bars and breakers, especially on garage and exterior walls.
200 Amp Panel Upgrade Atlanta: Choosing the Right Size
The right size depends on what you run today and what you plan to add. Before we recommend anything, we do a load calculation based on your square footage, appliances and HVAC equipment. For most single-family homes, a 200 amp panel upgrade Atlanta homeowners choose gives enough capacity for modern living plus room to grow.
100A
BASIC SERVICE
Smaller or older homes with gas heat and modest electric loads. Often maxed out once central air or an EV charger is added.
150A
MIDDLE STEP
A size some homes received in past upgrades. Works for many mid-size homes but leaves little room for new loads.
MOST COMMON
200A
MODERN STANDARD
Handles central HVAC, electric appliances, a home office and a Level 2 EV charger, confirmed by a load calculation.
320A+
LARGE OR ALL-ELECTRIC
Large homes, multiple EV chargers, pools, workshops or a big addition. Service size is coordinated with the utility.
Sometimes a full upgrade is not needed. If the panel is safe and has capacity but is out of breaker spaces, a subpanel can add circuits. If capacity is the problem, a 200 amp panel upgrade Atlanta families can grow into is the long-term fix, and it means your next project, like an EV charger, heat pump or hot tub, does not start with a panel problem.
Breaker Box Replacement Atlanta vs. a Full Service Upgrade
Not every panel job is the same size. When people call about a breaker box replacement Atlanta homeowners often picture one thing, but there are three common paths, and the assessment tells us which one fits your home.
Panel swap, same capacity
The existing panel is unsafe, damaged or a problem brand, but the service size is fine. This is the panel replacement Atlanta insurers most often ask about. We replace the panel and breakers and keep the existing service.
Full service upgrade
The home needs more capacity. We replace the panel and usually the meter base, service entrance conductors and grounding, then the utility reconnects at the higher rating.
Subpanel addition
The main panel is sound with spare capacity but no open spaces. A subpanel near the garage, basement or addition adds circuits without replacing the main.
What Every Electrical Panel Upgrade Atlanta GA Job Includes
Whether it is a breaker box replacement Atlanta homeowners need for safety or a full service upgrade for capacity, every job we do includes the same core steps.
âś“ Load calculation
So the new panel is sized for your current and planned loads.
âś“ AFCI and GFCI protection
Combination or dual function breakers wherever current code requires them.
âś“ Meter base and service conductors
Replaced when the service size or their condition calls for it.
âś“ Surge protection option
A whole-home surge protector installed at the panel if you want one.
âś“ Typed circuit directory
Every breaker labeled so you know exactly what it controls.
âś“ New panel and breakers
A modern load center with breakers matched to each circuit’s wire size.
âś“ Grounding and bonding update
Ground rods, bonding to water and gas piping, and proper neutral and ground separation.
âś“ Exterior emergency disconnect
Added at the service wherever current code requires one.
âś“ Permit and inspection
We pull the permit, meet the inspector and close it out.
âś“ Clean job site
The old panel hauled away and the work area left clean.
Our Panel Upgrade Process, Step by Step
A clear process keeps your electrical panel upgrade Atlanta GA project predictable, from the first call to the final inspection.
Assessment and load calculation
A licensed electrician checks your panel, meter, grounding and wiring, and asks what you plan to add.
Installation day
Power is off while we remove the old panel, set the new one and move every circuit over.
Written quote
You get the scope, materials and permit fees in writing. Work starts only after you approve it.
Inspection and reconnection
The city or county inspector checks the work, then the utility restores full power.
Permit and utility scheduling
We pull the permit and coordinate the disconnect with Georgia Power, your EMC or your city utility.
Final walkthrough
We show you the new panel, the circuit directory and the main shutoff, and answer your questions.
How Your Panel Upgrade Quote Is Built
We do not use a flat price list for panel work, because no two services are the same, and every electrical panel upgrade Atlanta GA quote we write starts with seeing the job. After the assessment you get a written quote based on your home, and the price you approve is the price you pay unless you change the scope.
âś“ Written quote before any work
âś“ Permit fees shown up front
âś“ No surprise add-ons
WHAT GOES INTO A PANEL QUOTE
Current and new service size
Going from a 60 amp fuse box to 200 amps involves more work than going from 100 to 200.
Meter base and service entrance
Whether the equipment on the utility side needs to be replaced too.
Grounding and bonding
Older homes often need new ground rods and bonding to meet code.
Panel location
An open garage wall is quicker than a panel buried in a finished basement.
Number of circuits
How many circuits move over, and whether new ones are being added.
Permits and utility
Fees and scheduling vary by city, county and utility provider.
Why Choose H & W Solution Partners for Your Panel Upgrade
As a licensed electrician Atlanta GA property owners can verify, we treat panel work as the most important job in the building, because everything else runs through it.
Licensed Georgia contractor
Every panel job is done under a state electrical contractor license, with a permit and a passed inspection.
Sized by the numbers
We run a load calculation before recommending a size, so your electrical panel upgrade Atlanta GA project is not oversized or left short on capacity.
Permits and utility handled
We deal with the permit office, the inspector and the utility so the project does not stall waiting on paperwork.
Clean, labeled, documented
A neat panel, a typed circuit directory and a closed permit you can hand to your insurer or a future buyer.
Panel Upgrades Across Atlanta and the South Metro
We handle every electrical panel upgrade Atlanta GA homeowners need inside the city, plus panel replacements and service upgrades in these nearby communities.
ATLANTA, GA
Intown bungalows and mid-century homes often still run on 100 amp service. Every electrical panel upgrade Atlanta GA permit goes through the City of Atlanta Office of Buildings.
FAYETTEVILLE, GA
Panel upgrades for established Fayette County neighborhoods and newer homes adding EV chargers and generators.
PEACHTREE CITY, GA
Service upgrades for garages charging golf carts and EVs, plus panel swaps in the older villages.
NEWNAN, GA
Careful panel and service work for historic homes near downtown and growing Coweta County subdivisions.
ELECTRICIAN IN NEWNAN, GA
GRIFFIN, GA
Replacing fuse boxes and aging panels in Spalding County homes and small businesses, with the same panel replacement Atlanta standards and permits.
HAMPTON, GA
A 200 amp panel upgrade Atlanta crews like ours handle often for Henry County homes adding workshops, additions and Level 2 chargers.
Related Electrical Services
An electrical panel upgrade Atlanta GA homeowners book often goes hand in hand with these jobs. Each one has its own page with more detail.
FEDERAL PACIFIC / ZINSCO PANEL REPLACEMENT
Federal Pacific Stab-Lok and Zinsco panels are known for breakers that may fail to trip during an overload. If your home still has one, we replace it with a modern panel.
FEDERAL PACIFIC PANEL REPLACEMENT
WHOLE-HOME SURGE PROTECTION
A panel-mounted surge protective device that guards HVAC control boards, appliances and electronics against lightning and utility surges, which hit metro Atlanta hard every summer.
EV CHARGER INSTALLATION
Level 2 charger installs for Tesla, Ford, Rivian, Chevy and every other EV. We check panel capacity, run a dedicated 240 volt circuit and mount the charger where the cable actually reaches.
GENERATOR INSTALLATION
Standby generator wiring plus manual or automatic transfer switches, so the fridge, HVAC, sump pump and medical equipment keep running when a summer storm takes out the power.
GENERATOR INSTALLATION
HOUSE REWIRING
Full and partial rewiring for homes with knob and tube, ungrounded two prong circuits or aluminum branch wiring. We plan the work room by room to keep wall openings to a minimum.
ELECTRICAL INSPECTION
Whole-home safety checks for buyers, sellers, landlords and insurance renewals, with a clear written list of what passes and what needs attention.
ELECTRICAL INSPECTION SERVICE
Electrical Panel Upgrade Atlanta GA FAQs
Straight answers about sizing, permits, timing and the utility. Still have a question? Call 404-507-6173.
How do I know if I need an electrical panel upgrade?
Common signs are breakers that trip often, lights that dim when large appliances start, a warm or buzzing panel, a fuse box, a Federal Pacific or Zinsco panel, or plans to add an EV charger, heat pump or addition. An on-site assessment with a load calculation tells you for sure.
What is the difference between a 100 amp and a 200 amp panel?
A 100 amp panel suits a smaller home with modest electric loads. A 200 amp panel supports central HVAC, electric appliances, a home office and a Level 2 EV charger, with room left for future projects. That is why a 200 amp panel upgrade Atlanta homeowners choose is the most common job we quote.
How long does an electrical panel upgrade take?
Most residential panel upgrades take about one working day on site. Power is off for part of that day while the old panel comes out and the new one goes in. Inspection and utility reconnection timing depends on your city or county.
Do I need a permit for a panel upgrade in Atlanta?
Yes. Panel upgrades and replacements need an electrical permit and an inspection. We pull the permit through the City of Atlanta Office of Buildings or your county, including Fayette, Coweta, Spalding and Henry, and meet the inspector for you.
Will Georgia Power need to be involved?
For a service upgrade, yes. The utility disconnects and reconnects service at the meter. We coordinate that with Georgia Power, your local EMC or your city utility, so you do not have to make those calls yourself.
How much does an electrical panel upgrade cost in Atlanta?
Every panel job is quoted on its own details. Price depends on your current and new service size, whether the meter base or service entrance needs replacing, grounding work, panel location and the number of circuits. You get a written quote before any electrical panel upgrade Atlanta GA work begins.
Do I need a panel upgrade before installing an EV charger?
Not always. A load calculation shows whether your panel can carry a dedicated 240 volt charger circuit. Many 100 amp homes need an upgrade or a load management device first, while most 200 amp homes have room.
Should I replace a Federal Pacific or Zinsco panel?
We recommend it. Both brands have well-documented breaker problems, and many insurers and buyers’ inspectors flag them. A panel replacement Atlanta inspectors approve removes the question for good.
Is breaker box replacement the same as a panel upgrade?
Not quite. A breaker box replacement Atlanta homeowners ask about swaps the panel at the same capacity, while a panel upgrade increases capacity and often includes the meter base and service conductors. The assessment tells us which one your home needs.
